NOTICE OF SOFTWARE RELEASE: 682 Firmware v1.15.01
02/09/26

•	Corrected issues with time and date not saving correctly via SD and ST EDP commands
•	Corrected multiple Fieldbus issues introduced in V1.15.00
•	Corrected issues with Australia regulatory mode not matching OIML in some instances


NOTICE OF SOFTWARE RELEASE: 682 Firmware v1.14.00
12/11/25

•    Adding the peak hold feature to the 682
•    Fixed Average count weight with shrink <SWC> improper rounding when shrink is 0
•    Renamed Bluetooth to WPAN in commands and HMI
•    Added pipe character to keyboard for LL3 formatting
•    Fixed truck records from overwriting EDP config on the SD card


NOTICE OF SOFTWARE RELEASE: 682 Firmware v1.13.00
10/31/25

•    Adding the check weighing program feature to the indicator


NOTICE OF SOFTWARE RELEASE: 682 Firmware v1.12.02
9/11/25

•    Correct an issue where removing the coin cell battery causes issues booting


NOTICE OF SOFTWARE RELEASE: 682 Firmware v1.12.01
9/9/25

•    Setpoints now trigger correctly with serial scales
•    Truck program is now compatible with serial scales


NOTICE OF SOFTWARE RELEASE: 682 Firmware v1.12.00
8/29/25

•     Added batch mode presets feature
•     Changed number of setpoints from 8 to 20
•     Added custom input stream capabilities
•     Added demand mode feature
•     Capacity reading on the webserver is incorrect
•     Zero can shift when returning from larger division range
•     Tares not working correctly with linear calibration points in certain scenarios
•     Fieldbus – Added a reset process to the 682 that resets the module
•     AZT – Canada mode incorrectly allows tracking off more than the allowed max
•     Stored tare values of the scale can now be viewed even when the scale is in overload
•     Fieldbus – Corrected issue with command status 4
•     Fieldbus – Corrected issue with command status 5
•     Fieldbus – Corrected issue with command status 5
•     Fieldbus – Multi-use value 1 register only updates after commands 11,12 and 41
•     Fieldbus – Weight registers only showing primary weights
•     Fieldbus – Calibration commands 35, and 36 fail with calibration status 3 each time
•     MRMI – AZT range should be based on range 1
•     Setpoints – Hysteresis not working with relative setpoints
•     Zero Range - Should based on the smallest weighing range or segment
•     User specified overload type is defaulted if regulatory mode is changed at the same time
•     Industrial Mode – REG.UNDERLOAD setting not working as expected
•     Custom Units – Uppercase letters show as lowercase in weight results
•     Audit – Changing gravity parameters should increment the config counter 
•     Default UserString1 softkey label if left blank
•     Australia – Underload should work the same as OIML
•     NTEP and Canada overload setting automatically reverts to FS+2%
•     OIML and Australia not using FS + 9D for overload when following a resetconfiguration command


NOTICE OF SOFTWARE RELEASE: 682 Firmware v1.11.05
7/24/25

•	Add support for multiple classes of SD card


NOTICE OF SOFTWARE RELEASE: 682 Firmware v1.11.04
3/7/25

•	Keypad error during truck in/out operation
•	Truck Reg menu error message causes stuck display


NOTICE OF SOFTWARE RELEASE: 682 Firmware v1.11.03
2/28/25
•     Add P1, P2 ,P3 ,P4 commands for printing auxiliary formats
•     Add soft keys for print and clear accumulator


NOTICE OF SOFTWARE RELEASE: 682 Firmware v1.11.00
2/19/25

Non-Legally relevant changes:
•     Count Average feature addition
•     Shrink % and Clear Shrink softkeys


NOTICE OF SOFTWARE RELEASE: 682 Firmware v1.10.02
1/13/25

Non-Legally relevant changes:
•     Update firmware to handle new rev of ADC chip


NOTICE OF SOFTWARE RELEASE: 682 Firmware v1.10.01
11/14/24

Non-Legally relevant changes:
•     <TR3> token being duplicated from <TR2>


NOTICE OF SOFTWARE RELEASE: 682 Firmware v1.10.00
10/10/24

Non-Legally relevant changes:
•     Serial Scale – Non-default units do not work properly when using RLWS format
•     USB Port – In certain situations the USB port blocks printing and streaming on other ports
•     Calibration – Cannot perform just a span or linear point calibration without error
•     Add feature for count averaging as well as custom messaging on the screen


NOTICE OF SOFTWARE RELEASE: 682 Firmware v1.09.00
04/03/24

Non-Legally relevant changes:
•     Added support for new display board


NOTICE OF SOFTWARE RELEASE: 682 Firmware v1.08.00
02/07/24

Non-Legally relevant changes:
•     Softkeys – STOP, GO and OFF softkeys added to control Aux #1-#3 
•     Audit trail – If the audit jumper is set to off counters were not incremented 
•     Audit trail – zero calibration not causing increment 
•     No matter the REGULAT setting, DUMPAUDIT always says NTEP 
•     Stream token for Weightronix mode should be uppercase 
•     Serial scale Toledo SF#1 does not work properly when primary units are set to KG 
•     Serial stream WeighTronix stream output is incorrect when using grams 
•     Serial stream Minebea stream output is incorrect when using OZ or T 
•     Serial scale Minebea format does not work properly when receiving OZ or T 


NOTICE OF SOFTWARE RELEASE: 682 Firmware v1.07.00
11/16/23
Non-Legally relevant changes:
•	Keyed tares must be rounded to nearest display division
•	Add Minebea stream format 
•	Truck register screen does not identify which weight is shown on the display 
•	Tare rounding issue


NOTICE OF SOFTWARE RELEASE: 682 Firmware v1.06.00
07/19/23
Non-Legally relevant changes:
• 	Add support for printing alternate units to the TRx print tokens


NOTICE OF SOFTWARE RELEASE: 682 Firmware v1.05.00
06/02/23
Non-Legally relevant changes:
• 	Add capability to press softkeys from digital inputs


NOTICE OF SOFTWARE RELEASE: 682 Firmware v1.04.03
05/04/23
Non-Legally relevant changes:
• 	Addressed another issue with the Range 1 capacity being changed incorrectly


NOTICE OF SOFTWARE RELEASE: 682 Firmware v1.04.02
03/28/23
Non-Legally relevant changes:
• 	Range 1 capacity resets to 6 after a power cycle


NOTICE OF SOFTWARE RELEASE: 682 Firmware v1.04.01
03/1/23
Non-Legally relevant changes:
• 	Range 3 is shown at or above capacity even when not configured


NOTICE OF SOFTWARE RELEASE: 682 Firmware v1.04.00
02/17/23
Legally relevant changes:
• 	Add Australia regulatory parameter


NOTICE OF SOFTWARE RELEASE: 682 Firmware v1.03.00
12/13/22
Non-Legally relevant changes:
• 	Fieldbus – Sending 10 command to a setpoint value causes lock up
• 	Truck Mode – Sometimes a truck weigh-in results in incorrect register values


NOTICE OF SOFTWARE RELEASE: 682 Firmware v1.02.01
10/11/22
Non-Legally relevant changes:
•     EDP Command – DIN command not working correctly
•     Batching – Push tare feature is locking up the indicator
•     Streaming – Corrected issue with stream frame output formats


NOTICE OF SOFTWARE RELEASE: 682 Firmware v1.02.00
09/08/22
Non-Legally relevant changes:
•	Accumulator – Not surviving power cycle
•	Accumulator – Printing from the menu does not show correct units
•	Accumulator – Not cleared with a reset configuration 
•	Alibi – Not accepting more than 13 prints 
•	Alibi – Display will not properly show the record number over 999
•	Alibi – Record can not store more than 256 characters 
•	Alibi – If first line print format is greater than 19 characters the time/date is overridden 
•	Digital Inputs – Held inputs not working correctly 
•	Digital Input – The input function CLEAR not working properly 
•	EDP – KTARE command exceeding capacity responds OK 
•	EDP – ALIBI.PRINT command not working 
•	Printing - <NOW> token not working correctly 
•	Printing – Multiple consecutive numbers in one format prints different numbers 
•	Printing – Consecutive number incrementing at incorrect point during print 
•	Printing – Consecutive number increments incorrectly with header formats 
•	Printing - <AA> token does not print with units, and is left justified 
•	Printing – Print formats do not allow for more than 30 tokens total 
•	Printing – Header formats not working correctly 
•	Printing – Header format limits to only 100 characters
•	Printing – Does not print unknown token correctly 
•	Printing – Gx/Tx/Nx do not work if number is less than weight digits
•	Printing - <AA> token prints blank 
•	Printing - <A> token prints dashes if accumulator value exceeds 7 characters
•	Remote Scale – Net weights not working properly 
•	Soft keys – Removed unused options 
•	Tare – The error message is missing for keyed tare exceeding capacity
•	Truck – Printing truck records multiple times causes lockup
•	Truck – Some ID’s can not be weighed out 
•	Truck – ID entry can lock up at times 
•	Truck – Sometimes weighed in ID does not appear on the register 
•	Truck – Truck register is not cleared during a reset configuration 
•	Web server – Buttons not working 


NOTICE OF SOFTWARE RELEASE: 682 Firmware v1.01.01
07/21/22
Non-Legally relevant changes:
•	Remote scale lockup issue
•	SU token decimals are not being removed


NOTICE OF SOFTWARE RELEASE: 682 Firmware v1.01.00
07/14/22
Non-Legally relevant changes:
•	Expand support more different transfer speeds for SD cards
•	Batch Menu – Correct error with messages when using the user menu
•	Truck Mode – Allow tare actions to occur concurrently with truck mode operation
•	Print Destination – Setting this parameter to option card when no card is installed causes a lockup
•	SX/EX commands not working for Wi-Fi/BT ports
•	SX/EX commands not working for dual serial option card
•	EDP command response for BATSTATUS has an extra terminator
•	Max date format is incorrect


NOTICE OF SOFTWARE RELEASE: 682 Firmware v1.00.02
06/22/22
Legally relevant changes:
•	Fixed an issue with the stream restrictions when in OIML mode and set to STRLFT 


NOTICE OF SOFTWARE RELEASE: 682 Firmware v1.00.01
05/16/22
Legally relevant changes:
•	Resolved an underload issue that impacts the OIML mode. 


NOTICE OF SOFTWARE RELEASE: 682 Firmware v1.00.00
03/28/22
•	Initial product release